A standing seam metal roof is built from long vertical panels that lock together along raised seams, with every fastener hidden underneath the metal instead of drilled through it. That one design decision is the reason these roofs outlast almost everything else installed in South Florida. There are no exposed screw heads to back out, no rubber washers baking in the sun, and no field of tiny holes for wind-driven rain to find.
Zen Metal Roofs installs standing seam roofs across Miami-Dade, Broward, and Palm Beach counties using Englert panel systems tested and approved for Florida's High Velocity Hurricane Zone (HVHZ), the strictest wind code in the country. We are certified Englert installers, and the crews on our jobs have been installing metal, and only metal, for more than 15 years.
Call Zen Metal Roofs directly: (786) 284-6994 | Free written estimate, same-week scheduling
Why Standing Seam Is the Right System for South Florida
Miami weather works on a roof three ways at once: hurricane wind, near-daily summer rain, and relentless heat and sun. Standing seam is the rare system engineered against all three.
Hurricane Wind
Panels are held down by concealed clips that screw to the roof deck and are gripped inside the seam. Wind uplift gets spread across the entire panel instead of concentrating at screw holes, which is where exposed fastener roofs fail first. Every Englert system we install carries a Miami-Dade Notice of Acceptance (NOA), the product approval that proves an assembly passed HVHZ testing for wind, water, and impact.
Driving Rain
The seams stand up above the water line, so heavy rain sheets off the panel instead of pooling against fastener penetrations. Fewer penetrations means fewer future leaks.
Heat and Sun
Panels come factory finished in Kynar 500, a high-performance resin coating made to reflect solar energy instead of absorbing it, refered to as Englert’s ULTRA-Cool Finishes. Reflectivity is measured by the Solar Reflectance Index (SRI), a 0 to 100 scale of how well a surface rejects heat. Englert's ULTRA-Cool finishes achieve SRI values of 29 or higher, used cool-roof benchmark for steep-slope residential roofs.
Salt Air
For homes near the water we switch from steel to aluminum panels, because salt air slowly corrodes steel and aluminum does not rust. It is a more expensive panel, and on the coast it is the correct one.
“Metal is straightforward for us. I don't get complicated with installs, and everything I do, I do by code. If I have to spend extra money to make sure a roof is not a headache later, I spend it. That's the way I run the business, because I run the installations.”
Eduardo Garcia, Founder, Zen Metal Roofs
The Englert Systems We Install
We build every standing seam roof around Englert panels, and the reason is quality control you can see. Englert runs its own in-house paint line instead of shipping coils out to a third-party painter, which is where cheaper panels lose color consistency and coating adhesion. When Eduardo puts an Englert sample next to a third-party painted panel, homeowners spot the difference without being told which is which.
Englert's supply chain is also why our schedule holds. Material availability means we can treat a metal roof like a shingle job timeline-wise: if your roof is dried-in on a Monday, we are usually installing metal by the next Monday. Which panel is right depends on your roof geometry, slope, and exposure. That call gets made during the assessment, not from a price sheet. For the deeper story on the manufacturer, see why we build every roof around Englert panels.
Englert Series 1300: Our HVHZ Workhorse
-
Panel: 1.5 inch mechanically seamed standing seam. After the panels are laid, a seaming machine folds the metal over twice into a double lock. It is the strongest seam you can put on a residential roof, which is why it is our default in the hurricane zone.
-
Substrate: 24-gauge Galvalume with Kynar 500 finish. Galvalume is steel wrapped in an aluminum-zinc alloy coating that blocks rust from reaching the steel underneath.
-
Attachment: concealed floating clips. Metal expands in Miami heat, and floating clips let each panel move without stressing fasteners or wrinkling the surface.
-
NOA: HVHZ approved and verified through Miami-Dade Product Control.
-
Warranty: 40-year limited finish warranty, with an optional Englert weathertightness warranty available on qualifying installations.
-
Colors: 25 colors available, plus custom.
Englert Series 2000: The Snap-Lock Alternative
-
Panel: 1.75 inch snap-lock structural panel, Englert's most popular standing seam profile. Panels click into place over the clip, no field seaming required.
-
Substrate: Galvalume steel or aluminum in multiple gauges. On coastal projects we spec 0.040 aluminum, a heavy panel chosen because salt air corrodes steel.
-
Requires: roof slope of at least 3:12, meaning the roof rises 3 inches for every horizontal foot. Below that, we use the Series 1300 double lock instead, because low slopes hold water longer and need the tighter seam.
-
Testing: tested and documented for wind uplift, water penetration, air infiltration, and fire.
-
Colors: 25 colors available, plus custom.
Englert Standing Seam Metal Roof Panels
Outlasts Shingle Roofing
Englert produces standing seam metal roofs that provide long-lasting performance. Englert roofs surpass traditional asphalt shingles with their potential lifespan of 50 years or more through proper maintenance. The extended lifespan of Englert roofs results in fewer replacements while providing Miami homeowners with less hassle and increased peace of mind amidst challenging weather conditions. Snap lock and mechanically seamed systems make these standing seam metal panels a superior permanent roofing solution that delivers better longevity and durability compared to exposed fastener panels.
30 Year Warranty
Peace of mind comes standard with every roof we install. Englert's premium finishes are backed by a 30-year limited warranty, giving homeowners long-term protection against fading, chalking, and corrosion. It’s not just about performance—it’s about confidence in a roof that’s built to last and backed by one of the most respected names in metal roofing. This warranty also covers materials and coatings, ensuring that each standing seam roof panel maintains its color and strength for decades.
Energy Efficient
Metal roofing does more than protect—it helps you save. Englert panels are designed with energy savings in mind. Reflective coatings help reduce heat absorption, which can make a noticeable difference in keeping your home cooler during Miami’s hottest months. That means less strain on your AC and the potential for lower utility bills—all while reducing your environmental footprint with a roofing system that performs and lasts. With the inclusion of stiffening ribs or pencil ribs, the panel strength is further improved, helping to reduce oil canning while maintaining optimal performance.
No Exposed Screws
With a standing seam system, you get a cleaner, more reliable finish—because there are no exposed screws. Englert’s roofing panels are designed to lock into place with hidden fasteners, which not only improves the look but also reduces the risk of leaks and long-term wear. It’s a smart design that adds both strength and style to your roof. Standing seam metal roofing systems often include male and female leg panel designs that interlock without the need for visible screws, enhancing overall system durability.
How Standing Seam Compares to Other Roofs
Most of the roofs we replace are aging shingle or exposed fastener metal. Here is the honest side-by-side. Deciding between standing seam and a metal tile look instead? Our comparison guide, Standing Seam vs. Metal Tile, covers design, weight, HOA rules, and solar in depth.
Our Installation Process,
Start to Finish
Eduardo runs the installations personally, and the process is the same whether the home is a small ranch or a cut-up roof over 8,000 square feet.
1) Roof and structure assessment. We evaluate the existing roof and what is under it, outside and in, and document everything we find with you. The most common surprises in South Florida homes are termite-damaged decking and unpermitted past work, and finding them now is what prevents mid-project change orders later.
2) Permits and paperwork. We prepare and file the HVHZ permit package, including the NOA documents for every component going on your roof. Timelines vary by city, and we handle the follow-up.
3) Tear-off and deck repair. Old roofing comes off and any compromised wood gets replaced. We do not install over bad decking, because clips only hold as well as the wood they are screwed into.
4) Dry-in with premium synthetic underlayment. Underlayment is the waterproof membrane between the deck and the metal. Ours is a woven synthetic that resists heat, wind, and mold, and it is a big part of why a modern metal roof is quiet in the rain. Your home is watertight from this point on.
5) Panel fabrication and layout. Panels are cut to the exact length of your roof, ridge to eave, so there are no horizontal joints anywhere on the field of the roof. Fewer joints, fewer places for water to try.
6) Clips and seaming. Clips are fastened to the deck and panels are locked over them. On Series 1300 roofs, the seamer then double-folds every seam. This is the step where experience shows, and our installers have been doing exactly this work for over 15 years.
7) Flashings and detail work. In Eduardo's experience, more roof leaks start at roof-to-wall transitions and flashings than anywhere else, so the detail work gets treated as the job, not the finish line.
8) Inspections and closeout. We schedule every city inspection through final, register your warranties, and walk the finished roof with you.
What Does a Standing Seam Roof Cost in Miami?
In 2026, most of our standing seam installations in Galvalume steel run $12 to $18 per square foot installed, and a typical single-family project lands between $22,000 and $42,000. Aluminum for coastal homes runs a few dollars more per square foot, because the material costs more and coastal work calls for heavier 0.040 panels.
What moves the number on your specific roof:
-
Roof size, pitch, and complexity. Cut-up roofs with many hips, valleys, and penetrations take more panel work and more detail work.
-
Substrate choice: Galvalume inland, aluminum near the water.
-
Tear-off and the condition of the decking underneath.
-
Permitting and engineering requirements for your city.
Every Zen proposal is written and fully itemized, and it names the exact product going on your roof along with its NOA number. An optional Englert weathertightness warranty is available on qualifying projects, typically $500 to $5,000 depending on roof size. For a full budget walk-through, see How Much Does Metal Roof Installation Cost in Miami?
PACE financing available: qualified homeowners can finance 100 percent of the project with no money down through Renew Financial, repaid through the property tax bill.
Recent Standing Seam Projects
Pompano Beach: the 11-quote roof
The homeowner collected eleven quotes before choosing us, and price was not why we won. The home sits close enough to the water and Eduardo specified 0.040 aluminum in Slate Gray, the heaviest residential aluminum panel we install, with stainless steel clips that will never corrode inside the seam. Thick aluminum can show oil canning, a visible waviness in the flat area of a panel, so panel handling and seaming were done to keep the finish dead smooth, and it shows.
Cutler Bay: hitting a real budget
This homeowner had a firm number he could not cross. We built the project around it: panels in Dark Bronze over 24-gauge Galvalume, with the financing structure he preferred. He still reaches out to tell us how the roof is doing, and what he mentions most is how respectful the crew was of his home.
Where We Install Standing Seam Roofs
We install across Miami-Dade, Broward, and Palm Beach counties: Miami, Coral Gables, Cutler Bay, Pembroke Pines, Fort Lauderdale, Pompano Beach, Boca Raton, and the communities around them. Find your city on our locations page for local permitting and HOA specifics.
Standing Seam Questions, Answered
How long does a standing seam metal roof last in Miami?
With proper installation, 40 to 70 years or more, even in South Florida heat and storm cycles. Unfortunately, Eduardo has inspected metal roofs leaking at year three and rusted through at year five, and the cause is nearly always a bad install or the wrong material, not the metal itself. The installer determines whether you get the lifespan you paid for.
Get Your Standing Seam Estimate
Tell us about your roof and we will come look at it, walk you through the options, and put a real number in writing.
By Eduardo Garcia | Florida Licensed Roofing Contractor | Certified Englert & BTR Installer | Last Updated: Aug 2026 | Serving Miami-Dade, Broward, and Palm Beach Counties